The 30 m sprint test is a simple field assessment of sprint performance. Depending on the setup, it can be used to examine acceleration from a stationary start or maximal-speed performance over a flying 30 m section. Results should only be compared when the protocol, timing method, surface and start procedure are matched.
The tables below come from separate published secondary references. The first describes a flying 30 m segment after a run-in and is attributed to Chu (1996) for world-class athletes. The second describes a standing-start acceleration test and is attributed to Davis et al. (2000) for UK 16–19-year-olds. Neither table is a universal standard: the underlying sample details and timing method are not documented here.
30 m Sprint Reference Bands: Flying and Standing Starts
Flying 30 m after a run-in: bands reproduced from the BrianMac table adapted from Chu (1996), described there as world-class athlete results. Time only the 30 m segment after acceleration. The source does not provide enough sample and timing detail to use these as validated population percentiles.
| Rating | Male (seconds) | Female (seconds) |
|---|---|---|
| Excellent | < 2.6 | < 3.0 |
| Above Average | 2.6 to 2.9 | 3.0 to 3.3 |
| Average | 2.9 to 3.1 | 3.3 to 3.5 |
| Below Average | 3.1 to 3.3 | 3.5 to 3.7 |
| Poor | > 3.3 | > 3.7 |
Standing-start 30 m acceleration: bands adapted from Davis et al. (2000) and presented as UK standards for ages 16–19. The original sampling and timing details are not established on this page, so treat the rounded categories as broad historical reference points:
| Rating | Male (seconds) | Female (seconds) |
|---|---|---|
| Excellent | <4 | <4.5 |
| Above Average | 4 to 4.2 | 4.5 to 4.6 |
| Average | 4.3 to 4.4 | 4.7 to 4.8 |
| Below Average | 4.5 to 4.6 | 4.9 to 5.0 |
| Poor | > 4.6 | > 5.0 |
What Is Needed for a 30m Sprint Test?
A 30 m sprint test can be used either from a stationary start to assess acceleration over 30 m, or as a flying 30 m to assess near-maximal speed after a run-in. These are different protocols and should not be compared directly. This page focuses on a standard 30 m timed sprint unless a flying start is stated. The basic equipment is:
- Flat surface
- Electronic timing gates where available; a stopwatch can be used for field testing, but hand-timed results should not be compared directly with electronically timed results
- Measuring tape
- Cones
- Assistant
For a standing start, mark a measured 30 m straight course and position the athlete consistently behind the start line. Use the same start cue and timing procedure on each trial. For flying times, mark and document the separate run-in distance.
How Is a Sprint Test Performed?
For a standard 30 m acceleration test, mark a start line and a finish line exactly 30 m apart. Keep the start procedure, timing method, surface and footwear consistent across participants and retests. A flying 30 m uses a separate run-in zone and should be treated as a different protocol.
- Complete a consistent, progressive warm-up appropriate for maximal sprinting before testing
- Take the sprint start position by keeping one foot behind the start mark
- Use a clearly defined start procedure and keep it identical across trials and retests
- The athlete sprints maximally from the start line through the 30 m finish line
- Timing starts at the agreed start signal or automatically at the start gate, depending on the protocol
- Timing stops when the athlete crosses the 30 m finish line
- Use a consistent number of maximal trials with sufficient recovery to minimise fatigue between attempts
- Record the fastest valid trial and the number of trials, rest interval and timing method
Record the result in seconds and compare it only with reference data collected using a comparable start, timing method, surface and distance.
Conditions and Interpretation
For a useful retest, document and where possible standardise the warm-up, start procedure, surface, footwear, weather, timing equipment, trial count and recovery. Hand timing and electronic gates can produce different results. Compare only like with like and use the athlete’s own previous tests as the most direct reference. For a dedicated maximal-speed protocol, see the Flying 30 m Sprint Test; for equipment selection, use the timing gates and sprint timing systems guide; and for related assessments, see the Power Testing hub.
The flying bands were adapted from Chu (1996) in Mackenzie’s Flying 30 metre Test; the standing-start bands were adapted from Davis et al. (2000) in Mackenzie’s 30-metre Acceleration Test. The published summaries do not give enough detail about sampling, timing error or category boundaries to treat the labels as precise percentile cutoffs. They are not interchangeable.
References: Chu, D. A. (1996), Explosive Power and Strength; Davis, B. et al. (2000), Physical Education and the Study of Sport, 4th ed., p. 125. Values and protocol descriptions are attributed through the linked Mackenzie summaries.

